-
Finished your HSC? Check out our University Discussion, Non-School forums or help out next year's HSC students! -
YOU can help the next generation of students in the community! Share your trial papers and notes on our Notes & Resources page
Hsc Marathon 2009 - Chemistry (3 Viewers)
- Thread starter aero135
- Start date
gurmies
Drover
A general one would be:
R-OH + HO-R -----------> R-O-R + H2O
For cellulose formation:
HO-C6H10O4-OH + HO-C6H10O4-OH ------------> HO-C6H10O4-O-C6H10O4-OH + H2O
______________________________________________________________
Describe gamma decay
OOft, this is a hard one to do! Ill try my best in answering. Cellulose is a polymer of which the monomer units are glucose. it can be writtten as OH-(C6H12O6)-OH.
when glucose molecules combine to form cellulose, the OH on the right -hand C atom of one molecule combines with the OH of the left-hand Carbon atom of the next glucose molecule.
- for bonding to occur alternate glucose units must be inverted
-this bonding produces a very linear molecule. the geometry of the rings and the C-O-C bond angles cause this linearity
Q. Describe how Radioisotopes are produced?
when glucose molecules combine to form cellulose, the OH on the right -hand C atom of one molecule combines with the OH of the left-hand Carbon atom of the next glucose molecule.
- for bonding to occur alternate glucose units must be inverted
-this bonding produces a very linear molecule. the geometry of the rings and the C-O-C bond angles cause this linearity
Q. Describe how Radioisotopes are produced?
Last edited:
Some typical uses of petrochemicals are:
- vinyl acetate for paint, paper and textile coatings vinyl chloride for
- polyvinyl chloride PVC)
- resin manufacture
- ethylene glycol for polyester - textile fibers
- styrene which is important in rubber and plastic manufacturing.
Q. what masses of lithium, zinc and cadium need to be oxidised to produce a mole of electrons?
- vinyl acetate for paint, paper and textile coatings vinyl chloride for
- polyvinyl chloride PVC)
- resin manufacture
- ethylene glycol for polyester - textile fibers
- styrene which is important in rubber and plastic manufacturing.
Q. what masses of lithium, zinc and cadium need to be oxidised to produce a mole of electrons?
Last edited:
Its a process by which substances are vapourised and then condensed by cooling. with mixtures of liquids having similar boiling points multiple still heads in a fractioning collum condense and return some of the vapour several times with the more volatile liquids rising furthur up the collum before being drawn off
identify the term used to describe the process by which monomers are converted to a polymer
identify the term used to describe the process by which monomers are converted to a polymer
marcquelle
a.k.a. Michael...Hi!
polymerisation?
gurmies
Drover
Cyclohexane and Cyclohexene were used in the school laboratory as they are colourless and liquid at room temperature meaning changes can be observed easily? Bromine water was used at the removal of HOBr by Cyclohexene causes the rapid decolourisation whereas cyclohexane does not change the bromine water...pretty crappy answer but it's the best I can do with no study of chemistry these holidays =(
Link the branching of LDPE to it's low density on a chemical level
Link the branching of LDPE to it's low density on a chemical level
bored of sc
Active Member
- Joined
- Nov 10, 2007
- Messages
- 2,314
- Gender
- Male
- HSC
- 2009
Not completely sure.
Since the chains are branched it means there is more space between neighbouring polymers. This implies there is a relatively low amount of matter from the polymer occupying a specific volume, hence a low density. In terms understandable, they are not packed closely together as the branched chains spread the neighbouring polymers apart further, leaving gaps of empty space.
Is that the kind of answer you are looking for?
bored of sc
Active Member
- Joined
- Nov 10, 2007
- Messages
- 2,314
- Gender
- Male
- HSC
- 2009
New question: What is general formula for an alcohol? Justify your answer with an example e.g. ethanol.
Fractional distillation is used to separate mixtures of miscible liquids, such as ethanol and water. The process depends on the components of the mixture having different boiling points. The liquid is heated so that it turns into a gas. The vapours pass up a fractionating column where they are gradually cooled. As each of the components of the mixture cools to its boiling point, it turns back into a liquid. The different components of the mixture condense at different levels in the fractionating column and thus may be separated.
Q. what would be the average molar mass of cellulose that conatained on average 300 glucose units per molecule? What would be the mass of the glucose from which this cellulose had been formed?
P.s my previous question was from conquering chemistry-hsc course, roland smith. it was from chapter 2 electrochemistry, question 19
i was also confused
Q. what would be the average molar mass of cellulose that conatained on average 300 glucose units per molecule? What would be the mass of the glucose from which this cellulose had been formed?
P.s my previous question was from conquering chemistry-hsc course, roland smith. it was from chapter 2 electrochemistry, question 19
i was also confused